With the new, expansible control system of TAIFUNO^®vision, you have the future technology fully under control.
Your are being led safely through the working process.

• without manual
• without long instruction
• once explained and you are fit

• process navigation system
• automatic connection of operating modes  
• dynamic, temperature-controlled heat recovery*
• Red-Eye^® Process control* and -visualization in Online-layout

• programme-controlled ventilating processes
• programm-controlled drying processes
• Automatic Standby-System
• Automatic Energy-Saving
• energy evaluation and operating costs recording*

Each TAIFUNO^®vision is equipped for connection to the WOLF-owned Service-Center. We only need your internet connection at our switchboard.

In case of a failure, experienced specialists in our headquarters do a first check „online“. Quickly and professionally - saving time and money.

So don't worry if you are far away from us.

With the Mode Lamp, even from a distance you have under control if your employees are using the efficient booth technology optimally.

In the modes of operation Cleaning, Spraying, Evaporating, Drying, Cooling and Energy-Saving, the lamp in the respective colour is shining. When Multi-Air is switched on additionally, the signal lamp is flashing.

This energy-saving function puts TAIFUNO^®vision automatically to a reduced air and heating capacity, when in mode of operation Spraying the spray gun is not actuated. When actuating again, the full capacity is reached again within few seconds.

The Multi-Air System is integrated between filter ceiling and lighting. The jets are installed sunk in the inclined side cladding; their blasting direction can be adjusted individually.

The Multi-Air System provides maximal process acceleration when evaporating and drying.

Time saving is up to 70% compared to the method without Multi-Air.  A partial flow of process air is acting as accelerator flowing at high speed out of the jets downwards and producing a turbulent flow around the object.

The TAIFUNO^®vision control system offers you various evaporating programmes.
The software also includes special evaporating programmes which are pre-adjusted in coordination with the leading paint manufacturers, simplifying considerably the use of water paints.

With these automatic programmes, the parameters temperature, air exit velocity and time are optimally adjusted to the respective paint, guaranteeing a maximum of process security.

By Red-Eye^® technology, drying in a combi-booth is newly defined. The system is marked by two decisive advantages: high process security and a clear reduction of heating costs.

During Red-Eye^® process, a laser-beam supported infrared temperature sensor is directed to the object by the multiple-axle swivel arm.

The heating installation is now regulated exactly according to the current object temperature which is permanently compared to the nominal value. The booth is heating only to the temperature actually required by the object / the paint.

By the combination Red-Eye^® and Multi-Air, up to 45 % of drying costs can be saved. Depending on the programme adjusted, the Multi-Air System is switched on immediately or after a certain delay.

The advantages of the Multi-Air-System in drying process are very well-known. Multi-Air is leading the warm air much more quickly and evenly to the object.

The temperature differents between upper and lower components is only minimal.

Therefore, the recirculating air temperature can still be decreased moreover, the recirculating air quantity is automatically reduced as soon as the object temperature is reached."

Light Evolution^© is the system which assures energy-saving, best lighting conditions in the booth and thus an optimal paint quality. A retrofit is possible in all WOLF - booths without any problems.

This reduction is due to a basically lower power consumption of LEDs. The decisive factor is the integration of Light Evolution© into the mode control of the spray booth TAIFUNO®vision: The lighting is permanently automatically adjusted to the process steps - it is integrated into the sprayer's normal working process.

The correct use of the technology is secured.

The classic Heat Recovery (HR) systems for spray booths are only in function during spraying. During drying, the warm exhaust air (up to 100 °C) is blown outside unused.

The TAIFUNO^®vision puts an end to this waste of energy. The heat recovery is fully in function in all modes of operation.

A new development by WOLF is the Dynamic Heat Recovery. So far, the plate heat exchangers have to be removed from one booth in summer in order to avoid undesired high booth temperatures. Thus, on cold summer days or in cooler morning hours, the HR cannot be used. With the dynamic VARIO©HR*, the heat exchanger remains in the booth. The air flow is only led through the heat exchanger, when the booth control signalizes heat requirement. When no heat is required, the air is automatically flowing past the HR.

A further advantage of VARIO©HR is the spontaneous availability of the HR. Even when in spraying operation at high outside temperatures the air flow is led past the HR, there is high heat requirement during subsequent drying. The control system recognizes this and automatically switches to heat recovery immediately. You are saving energy even in summer around the clock.

Heating energy consumption of a combi-booth in % per year.
Comparison valid at a mean annual temperature of 9 °C